A system on a chip or system on chip (SoC or SOC) is an integrated circuit (also known as an "IC" or "chip") that integrates all components of a computer or other electronic systems. It may contain digital, analog, mixed-signal, and often radio-frequency functionsâ€"all on a single substrate. SoCs are very common in the mobile computing market because of their low power-consumption. A typical application is in the area of embedded systems.
SoC integrates a microcontroller (or microprocessor) with advanced peripherals like graphics processing unit (GPU), Wi-Fi module, or coprocessor. If the definition of a microcontroller is a system that integrates a microprocessor with peripheral circuits and memory, the SoC is to a microcontroller what a microcontroller is to processors, remembering that the SoC does not necessarily contain built-in memory.
In general, there are three distinguishable types of SoCs. SoCs built around a microcontroller, SoCs built around a microprocessor (this type can be found in mobile phones), and specialized SoCs designed for specific applications that do not fit into the above two categories. A separate category may be Programmable SoC (PSoC), where some of the internal elements are not predefined and can be programmable in a manner analogous to the FPGA or CPLD.
When it is not feasible to construct a SoC for a particular application, an alternative is a system in package (SiP) comprising a number of chips in a single package. When produced in large volumes, SoC is more cost-effective than SiP because its packaging is simpler.
Another option, as seen for example in higher-end cell phones, is package on package stacking during board assembly. The SoC includes processors and numerous digital peripherals, and comes in a ball grid package with lower and upper connections. The lower balls connect to the board and various peripherals, with the upper balls in a ring holding the memory buses used to access NAND flash and DDR2 RAM. Memory packages could come from multiple vendors.
Structure
A typical SoC consists of:
- a microcontroller, microprocessor or digital signal processor (DSP) core â€" multiprocessor SoCs (MPSoC) having more than one processor core
- memory blocks including a selection of ROM, RAM, EEPROM and flash memory
- timing sources including oscillators and phase-locked loops
- peripherals including counter-timers, real-time timers and power-on reset generators
- external interfaces, including industry standards such as USB, FireWire, Ethernet, USART, SPI
- analog interfaces including ADCs and DACs
- voltage regulators and power management circuits
A bus â€" either proprietary or industry-standard such as the AMBA bus from ARM Holdings â€" connects these blocks. DMA controllers route data directly between external interfaces and memory, bypassing the processor core and thereby increasing the data throughput of the SoC.
Design flow
A SoC consists of both the hardware, described above, and the software controlling the microcontroller, microprocessor or DSP cores, peripherals and interfaces. The design flow for a SoC aims to develop this hardware and software in parallel.
Most SoCs are developed from pre-qualified hardware blocks for the hardware elements described above, together with the software drivers that control their operation. Of particular importance are the protocol stacks that drive industry-standard interfaces like USB. The hardware blocks are put together using CAD tools; the software modules are integrated using a software-development environment.
Once the architecture of the SoC has been defined, any new hardware elements are written in an abstract language termed RTL which defines the circuit behaviour. These elements are connected together in the same RTL language to create the full SoC design.
Chips are verified for logical correctness before being sent to foundry. This process is called functional verification and it accounts for a significant portion of the time and energy expended in the chip design life cycle (although the often quoted figure of 70% is probably an exaggeration). With the growing complexity of chips, hardware verification languages like SystemVerilog, SystemC, e, and OpenVera are being used. Bugs found in the verification stage are reported to the designer.
Traditionally, engineers have employed simulation acceleration, emulation and/or an FPGA prototype to verify and debug both hardware and software for SoC designs prior to tapeout. With high capacity and fast compilation time, acceleration and emulation are powerful technologies that provide wide visibility into systems. Both technologies, however, operate slowly, on the order of MHz, which may be significantly slower â€" up to 100 times slower â€" than the SoC's operating frequency. Acceleration and emulation boxes are also very large and expensive at over US$1 million. FPGA prototypes, in contrast, use FPGAs directly to enable engineers to validate and test at, or close to, a system’s full operating frequency with real-world stimuli. Tools such as Certus are used to insert probes in the FPGA RTL that make signals available for observation. This is used to debug hardware, firmware and software interactions across multiple FPGAs with capabilities similar to a logic analyzer.
In parallel, the hardware elements are grouped and passed through a process of logic synthesis, during which performance constraints, such as operational frequency and expected signal delays, are applied. This generates a logical netlist which is a file describing the circuit as a collection of connected silicon gate elements from a library provided by the silicon manufacturer.
This netlist is used as the basis for the physical design (place and route) flow to convert the designers' intent into the polygonal design of the SoC. Throughout this conversion process, the design is analysed with static timing modelling, simulation and other tools to ensure that it meets the specified operational parameters such as frequency, power consumption and dissipation, functional integrity vs. the RTL and electrical integrity.
When all known bugs have been rectified and these have been re-verified and all physical design checks are done, the physical design files describing each layer of the chip are sent to the foundry's mask shop where a full set of glass lithographic masks will be etched. These are sent to the wafer fabrication plant to create the SoC dice before packaging and testing.
Fabrication
SoCs can be fabricated by several technologies, including:
- Full custom
- Standard cell
- Field-programmable gate array (FPGA)
SoC designs usually consume less power and have a lower cost and higher reliability than the multi-chip systems that they replace. And with fewer packages in the system, assembly costs are reduced as well.
However, like most VLSI designs, the total cost is higher for one large chip than for the same functionality distributed over several smaller chips, because of lower yields and higher non-recurring engineering costs.
Benchmarks
SoC research and development often compares many options. Benchmarks, such as COSMIC, are developed to help such evaluations.
See also
- List of system-on-a-chip suppliers
- PSoC
- Electronic design automation
- Post-silicon validation
- Single-board computer
- Network on a chip
- Radio-on-a-chip
- ARM architecture
- Socionext
References
Further reading
- Badawy, Wael; Jullien, Graham A., eds. (2003). System-on-Chip for Real-Time Applications. Kluwer international series in engineering and computer science, SECS 711. Boston: Kluwer Academic Publishers. ISBN 9781402072543. OCLC 50478525. 465 pages.
- Furber, Stephen B. (2000). ARM system-on-chip architecture. Boston: Addison-Wesley. ISBNÂ 0-201-67519-6.Â
External links
- SOCC Annual IEEE International SOC Conference
- Baya free SoC platform assembly and IP integration tool
